 |
|
 |
|
 |
|
 |
|
 |
|
|
|
|
|
Features
Molded highly reflective tape ensures that the speed bumps are visible even on a dark night. Optional cat's eye reflectors further enhance visibility to alert drivers well in advance. The bumps have a channeled bottom to facilitate drainage as well as to cover cabling or piping.
Easy Rider® speed bumps are the ideal maintenance-free parking lot solution. In addition to enhancing parking lot safety, the bumps can lower insurance premiums for lot owners.
The Easy Rider® is available in 120 cm and 180 cm lengths including end caps to protect the speed bump ends and vehicles. GNR rubber speed bumps are covered by a 3 year warranty.
Easy Rider® Speed Bumps are:
- Made of 100% recycled rubber
- Long lasting and cost efficient
- Reduces speed to 3-8 km/h
- High visibility at night
- Simple installation
- Product can be installed in sections to create varying lengths
- Will not warp, crack, chip or rot
- Can be installed on any road surface
- Resistant to ultraviolet light, moisture, oil, and extreme temperatures
- Temporary or permanent installation - Relocatable when resurfacing / maintaining road surfaces; products can be stored and re-used
- Channeled bottom for cabling and piping
- Lowers insurance premiums for lot owners
- Maintenance free
- 3 year warranty
Applications:
Used for the following situations:
- Safety of pedestrian and vehicle traffic requires improvement
- To further support and reinforce stop signs in parking lots
- High risk of accidents on residential streets and in parking lots need to be reduced
- Permanent or temporary lowering speed of motor vehicles is required
- Only temporary installation is allowed or required
- Installation on surfaces where only flexible rubber speed bumps may fully conform to the curvature of the road
|
|
|
Easy Rider® speed bumps
have been used in the following locations:
- Loyola Medical University
- US Army Corps of Engineers
- Luxor Hotel and Casino
- Best Western
- Carollsburg Condominium
- Greendale Mall
- Ryder Truck Rentals
- Lowes
- Whitlow Chevrolet
- Bethel Christian Center
- American Greetings Corp.
- Dairy Queen
- United Postal Service
- Wal Mart
- Dunkin Donuts
|
Installation Locations:
Shopping centers
School zones
Hotel entrances
Gas stations
Neighborhood intersections
Stop sign reinforcement
Parking lot gate entrances
Parking lots and garages
Gated communities
|
|
| |
|
|
| Dimensions |
| |
|
|
 |
|
Easy Rider Speed Bump
Dimensions:
(L) 120 cm x (W) 30,5 cm x (H) 5,7 cm - 14,5 kg.
(L) 180 cm x (W) 30,5 cm x (H) 5,7 cm - 23,1 kg.
Easy Rider End Cap
Dimensions:
(L) 23 cm X (W) 30,5 cm X (H) 5,7 cm - 2,5 kg.
|
| |
|
|
| |
| |
| Technical Specs |
| |
| |
|
Product Name:
Rubber Speed Bumps 5,7 cm thick
|
|
|
Models:
180 cm and 120 cm long
|
|
|
Product description:
1. Material: compression molded composite: 100% recycled rubber and polyurethane prepolymer
2. Physical properties of the rubber composite:
a. Density 17g/cm3 in (ASTM C642)
b. Durometer Hardness 70A ± 7 (ASTM D2240)
c. Tensile Strength 300 psi (ASTM D412)
d. Compression deformation 7% at 70psi, 68°F (ASTM D575)
e. Brittleness at Low temperature: -40°F (ASTM D746)
f. Freeze and thaw when exposed to de-icing chemicals no loss after 50 cycles (ASTM C672)
g. Coefficient of thermal expansion: 8 x10-5 in/in/°F (ASTM C531)
h. Weathering 70 hours at 158°F (ASTM D573)
- hardness retained 100% (± 5%)
- compressive strength 100% (± 5%)
- tensile strength 100% (± 5%)
- elongation retained 100% (± 5%)
3. Available models: 180 cm, 120 cm long
4. Finishing: Black recycled rubber composite with yellow, durable and reflective, in-molded pavement marking tape
|
|
|
|
|
Components:
a)100% recycled rubber from car and truck tires (NR, SBR)
b)polyurethane prepolymer
c)cat's eyes reflectors
d) yellow, durable and reflective in-molded pavement marking tape
|
| |
| |
| Installation Guide |
| |
|
Components
Easy Rider speed bumps
(356x13mm) rebar spikes for asphalt or lag bolts with metal shields for concrete - available at GNR
|
| |
| What You Need |
|
|
- Gloves, safety glasses
- Traffic cones, drums or barricades for securing the site
- Mallet
- Heavy duty electric drill
- 12mm masonry bit and, if installed with lag bolts: a masonry bit required for the metal shields - consult bit size on side of shield
- A drive socket and power tool for installation of the lag bolts
The flexible design of the Easy Rider Speed Bump allows the product to conform to the contour of uneven road surfaces and can be installed on both asphalt and concrete.
|
|
Installations Instructions for Asphalt: Installation of Easy Rider Speed Bumps with spikes
|
|
|
Step 1.
Drill 12mm diameter holes (75-100mm in depth) in the asphalt through the product's holes.
|
|
|
|
Step 2.
Drive rebar spikes (356x13mm) through the holes in the product.
|
|
** Speed bumps can also be installed on asphalt with lag bolts and shields. Please consult instructions below for installation using bolts and shields.
|
|
Installation Instructions for Concrete: Installation of Easy Rider Speed Bumps with lag bolts and metal shields
|
| |
|
Step 1.
Use M12x180 lag bolts and plastic shields.
|
|
|
|
|
|
| Step 2.
Drill 12mm diameter pilot holes (75-100mm in depth) through the product's installation holes.
|
 |
|
|
|
Step 3.
Remove the product; re-drill the holes for the diameter and depth required by the metal shields.
|
|
|
|
Step 4.
Install the metal shields, re-position the product and bolt with lag bolts.
|
|
|
|
Maintenance
|
|
|
| Speed bumps require minimal maintenance. Periodically inspect the bolts and tighten if necessary. |
| |
|
|
